Insulation Calculator

How much insulation do you need? R-value to add for your climate zone, depth and bags of blown-in cellulose or fiberglass, or which batts to buy — with ENERGY STAR targets.

Attic floor area ≈ the footprint of the house below it.
Old fiberglass or cellulose ≈ R-3 per inch. Measure in a few spots.
lb
Check the coverage chart printed on the bag — it’s the final word for that product.

Results

Area
1,500
Target R-value
R-60 (you have ≈ R-9)
R-value to add
R-51
Depth to add (settled)
14.6″ — blow about 17.5″ to allow for settling
Bags needed
≈ 110 bags (2,732 lb)

🛒 Shopping list

ItemQtyPrice each ($)Cost
Cellulose loose-fill insulation, 25 lb bag Many stores lend the blowing machine free with a 10–20 bag purchase110 bags$1,870.00
Insulation depth rulers (attach to joists) 5 rulers$5.00
Attic baffles / rafter vents (one per rafter bay at the eaves) Keep soffit vents open38 baffles$76.00
Canned spray foam (gaps & top plates) 2 cans$16.00
N95 respirator, goggles, long sleeves 1 kits$25.00
Estimated materials total$1,992.00

Prices are rough US starting points, not quotes — type in your local store’s prices. Taxes and delivery not included.

⚠️ Before insulating: seal air leaks (top plates, plumbing and wiring holes, the attic hatch) and keep insulation at least 3″ away from recessed lights not rated IC, chimneys and flues unless the product says otherwise.
💡 Targets follow ENERGY STAR / U.S. DOE guidance: attics R-49 to R-60 in most of the U.S. (R-30 to R-49 in the hottest zone); 2×4 walls R-13 to R-15, 2×6 walls R-19 to R-21; floors R-25 to R-30.
💡 R per inch used: cellulose ≈ 3.5, blown fiberglass ≈ 2.5, old insulation ≈ 3. Blown fiberglass needs more depth for the same R-value but weighs less.
💡 See the Attic Insulation Savings calculator for the payback on your energy bill.

How to do it

Difficulty: ModerateTime: One day for a typical attic (two people)

Tools you’ll need

  • Blowing machine (often free to borrow with bags)
  • Utility knife & straightedge (batts)
  • Headlamp, knee pads, plank to walk on joists
  • Respirator, goggles, gloves

Steps

  1. Walk only on joists (lay planks) — stepping between them goes through the ceiling.
  2. Seal air leaks first with foam and caulk: wire and pipe holes, top plates, the hatch.
  3. Fit baffles at the eaves so insulation doesn’t block soffit vents.
  4. Staple depth rulers to joists across the attic so you can see the target depth.
  5. Blow from the far end back toward the hatch, keeping the hose level; or roll batts snugly without compressing them.
  6. Insulate and weatherstrip the attic hatch (glue a batt or rigid foam to it).

Common mistakes

  • Blocking soffit vents — causes moisture and ice dams.
  • Compressing batts — a squashed batt loses R-value.
  • Covering non-IC recessed lights or knob-and-tube wiring (a fire hazard; get an electrician first).
👷 When to call a pro: If you see vermiculite (grayish-brown, pebbly) don’t disturb it — it may contain asbestos. Have it tested first.

Formula

R to add = target R − existing R; depth = R to add ÷ R per inch; loose-fill weight = area × depth × installed density; bags = weight ÷ bag weight

More DIY Projects calculators

← Browse DIY projects