Paver Driveways: How Deep to Dig, How Much Base, and Is Your Quote Fair?
A paver driveway is mostly hidden. The pavers you see are a couple of inches thick; under them is a bed of sand and a deep layer of compacted crushed stone that actually carries the car. Whether a driveway stays flat for decades or develops sunken wheel ruts is decided by that hidden part — which is also the easiest part of a quote to cut.
What’s under a paver driveway
The standard build-up recommended by the Concrete Masonry & Hardscapes Association (CMHA, formerly ICPI), from top to bottom:
| Layer | Residential driveway |
|---|---|
| Concrete pavers | 2⅜″ (60 mm) thick is recommended for residential driveways; 3⅛″ (80 mm) for streets and heavier traffic |
| Bedding sand | About 1″, screeded flat — not compacted before the pavers go down |
| Crushed-stone base | 6–8″ compacted; at least 6″ on well-drained soil |
| Geotextile (optional) | Recommended over clay, soils that stay wet, and where the ground freezes and thaws |
| Soil subgrade | Compacted, and sloped so water drains away |
On clay or in cold climates, many installers go deeper than the minimum — 10–12″ of base is common. Local soil decides, and it’s a fair question to ask any contractor.
A worked example: a 40 × 12 ft driveway
A single-car driveway 40 ft long and 12 ft wide is 480 ft². With 4″ × 8″ pavers, an 8″ base and 10% extra for cuts, the driveway paver calculator gives:
- Pavers: about 2,376 — roughly 7½ tons, or about 5 pallets
- Dig depth: about 11½″ (8″ base + 1″ sand + 2⅜″ paver)
- Soil to haul away: about 17 yd³ in the ground, which swells to about 21 yd³ once dug — roughly two dump-truck loads
- Crushed-stone base: about 20 tons
- Bedding sand: about 2 tons
That is a lot of material to move by hand, which is why most paver driveways are installed by a crew with a skid steer and a heavy plate compactor.
What it costs
2026 U.S. cost guides put a standard concrete-paver driveway at roughly $10–$20 per square foot installed; permeable and decorative pavers, natural stone and cobblestone cost more. For the 480 ft² example, that’s about $4,800–$9,600.
Materials — pavers, base and sand — come to only about $2,700 of that at typical supplier prices. The rest is digging, hauling, equipment, compaction and labor. Removing an old driveway first adds more: 480 ft² of old 3″ asphalt is around 9 tons of debris.
How to check a quote
Divide the quote by the area to get a price per square foot — the calculator does this for you. Then ask:
- How deep is the base, and is it compacted in layers? “4 inches of gravel” under a driveway is a warning sign. CMHA calls for compacting the base in lifts of about 4–6″.
- What paver thickness? Thin patio pavers aren’t meant for cars; look for at least 2⅜″ (60 mm).
- What edge restraint? Without restraint along the edges, tires slowly push pavers outward.
- What laying pattern? CMHA recommends 45° or 90° herringbone where cars drive, because it resists the push of starting, braking and turning tires.
- Are removal, hauling, geotextile and the permit included? Many towns require a permit where a driveway meets the street.
- How is it sloped? Water should drain away from the garage and house, not sit under the pavers.
A low price isn’t automatically bad, and a high one isn’t automatically a rip-off — but a contractor who can’t tell you the base depth is one to walk away from.
Material quantities are calculations; prices vary widely by region, site access and paver choice. Always get more than one itemized quote.
Frequently asked questions
How thick should pavers be for a driveway?
The Concrete Masonry & Hardscapes Association recommends 2⅜ in. (60 mm) thick concrete pavers for residential driveways, and 3⅛ in. (80 mm) pavers for streets and heavier vehicular traffic.
How deep should the gravel base be under driveway pavers?
CMHA guidance is 6–8 inches of compacted aggregate base for residential driveways, and at least 6 inches on well-drained soil. On clay, wet soil or in freeze–thaw climates, installers commonly use 10–12 inches, often over geotextile.
How deep do you dig for a paver driveway?
Add the base depth, about 1 inch of bedding sand and the paver thickness. For an 8-inch base and 2⅜-inch pavers, dig about 11½ inches below the finished surface.
How much does a paver driveway cost?
Standard concrete-paver driveways typically cost about $10–$20 per square foot installed in the U.S. in 2026 — roughly $4,800–$9,600 for a 40 × 12 ft driveway. Premium pavers, old-driveway removal and difficult sites cost more.
How many pavers do I need for a driveway?
Standard 4 × 8 inch pavers work out to 4.5 per square foot. A 480 sq ft driveway needs about 2,376 pavers including 10% for cuts — about 7½ tons.